Best Over Cabinet Lighting

These puck lights operate on their own with the on/off tap lens. The puck lights are also add-on puck lights for model numbers BRRC134 and BRRC135. These puck lights work with a remote. The remote is not included. The AA batteries are not included. The Wireless LED Puck Lights are super bright at 55 lumens. The LEDs are 3000K and give off a warm white glow. Use a remote to turn the puck lights ON/OFF up to 15 ft. away. Control up to 12 puck lights with one remote. Set the brightness to 50% or 100% with the preset dimmer buttons or use the – or + buttons to select the exact level of brightness. There is an optional timer that will automatically turn the lights off in 15, 30, 60 or 120 minutes. The puck lights mount with screws or adhesive tape (both are included). The lights operate on 3 AA batteries (not included) and have a run time of over 100 hours. The run time is 4 times longer than other battery operated puck lights. Measures 3.37 in. wide x 3.37 in. deep x 1.25 in. high.

The Brilliant Evolution Wireless LED Puck Light 6 Pack With Remote is super bright at 55 lumens. The LEDs are 3000K and give off a warm white glow. Use the remote to turn the puck lights ON/OFF up to 15 ft. away. Control up to 12 puck lights with one remote. There is also an ON/OFF tap lens. Set the brightness to 50% or 100% with the preset dimmer buttons or use the – or + buttons to select the exact level of brightness. There is an optional timer that will automatically turn the lights off in 15, 30, 60 or 120 minutes. The puck lights mount with screws or adhesive tape (both are included). The lights operate on 3 AA batteries (18 AA batteries included) and have a run time of over 100 hours. The run time is 4 times longer than other battery operated puck lights. Measures 3.37 in. wide x 3.37 in. deep x 1.25 in. high. Patented and patents pending.

See your home in the best possible light with a GE-branded Premium Linkable Light Fixture. This energy-efficient fixture is the ideal solution for any room in your home, adding light wherever extra light is needed. With the ability to link 30 fixtures while only using a single outlet, get the perfect amount of light for any size room. In addition to being able to plug into an outlet, the light can be wired directly to a wall switch using the optional GE-branded Direct Wire Junction Box to eliminate visible cords.

To achieve stylish accent lighting in moments, simply mount the light underneath or on top of kitchen cabinetry, shelving or bookcases using the keyhole slots located at the end of each fixture. In smaller enclosed areas, such as closets and pantries, use the lights to illuminate hard-to-see corners — the light’s slim design makes it convenient to place in locations with limited space. The toggle switch makes it easy to operate, allowing you to choose between high and low settings, as well as turn the light off. Make life a little brighter with a GE-branded Premium Linkable Light Fixture.

Specifications (LED strip)* LED Quantity/Type: 150xSMD5050 RGB* Input Voltage (to power supply): 100-240VAC, 50/60Hz* Power: 36W* LED Strip Width: 10mm* LED Strip Length: 16.4ft (5m)* IP Rating: IP30 (dry locations only) Items Included* (1x) RGB LED strip with adhesive back* (1x) Controller and 44-button wireless IR remote* (1x) Power supply Wiring* Unroll LED strip completely.* Any exposed wires on the other end of the LED strip must not touch one another (or any metal object), creating a short.* Connect the 4-pin connector of controller to that of the LED strip, making sure that the arrows line up.* Connect 5mm DC jack of power supply to controller.* Remove the plastic seal in the battery compartment of the wireless remote.* Double check that all connections are correct and secure, then plug in power cord. Note* While the included controller can handle the power requirement of two such strips, the power supply only has the capacity to drive a single strip.* Do not lengthen the LED strip by directly connecting an additional section to it.* Extension kits are available for adding additional strips.* Test all components before permanent installation.* Make sure that wires at the other end of the LED strip are not touching one another (or any metal object), which would create a short circuit. Electrical tape may be used to wrap each of those wire ends to isolate them.* The LED strip is cuttable every 3 LEDs, approx. every 4″, at the designated cut marks.